A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

铝合金型材柔性垫弯曲成形实验研究

进行两种典型铝合金型材的弯曲实验,研究主要工艺参数对弯曲过程的影响.结果表明,型材的截面形状、相对厚度及抗弯截面系数等是决定弯曲性能的主要因素.压辊的压入深度、柔性垫的性能以及型材的约束方式等是影响弯曲半径、截面变化的关键.对实验中主要缺陷和质量问题的产生及其控制进行分析和讨论.     

Study on the breakup lengths of free round liquid jets

IntroductionBreakup and atomization of roundliquidjetshad been widely used in internal combustion en-gines,gas turbines,and liquid rocket engines.Recently,with the development of scramjet en-gines and the deepening of fuel atomization re-search,it attract…     

冷挤压孔板残余应力场分析

 <正> 1.冷挤压孔板残余应力场 如图1所示,设理想弹塑性材料厚壁圆筒内半径为R_1,外半径为R_2,受内压P作用,卸载后,形成塑性半径ρ,此时,圆筒残余应力场为     

三轴相交度的一种测量方法

介绍了三个回转轴相交度的一种测量方法，并进行了测量不确定度分析。     

天然金刚石刀具单激励超声椭圆振动车削

设计并制造了一种单激励夹心式纵弯复合椭圆振动车削系统.在分析超声椭圆振动切削抑制刀具崩刃机理的基础上,利用该系统进行了天然金刚石刀具振动车削铝件的试验,证实了椭圆振动切削可以有效防止刀具崩刃.     

GT35硬质合金材料高温摩擦磨损特性研究

利用球-盘高温摩擦磨损试验机对GT35硬质合金进行摩擦磨损实验,研究了GT35硬质合金材料的摩擦磨损特性及机理。分析了不同温度和不同摩擦半径情况下GT35硬质合金的摩擦磨损行为。结果表明:在法向载荷不变的条件下,GT35硬质合金的摩擦系数和比磨损率均随温度的上升而增大,其摩擦系数和比磨损率随摩擦半径的增加也呈上升的变化趋势。     

进口水平投影可控的流线追踪内收缩进气道设计

为了满足两侧进气布局飞行器的乘波前体与进气道一体化设计要求,提出了一种进口水平投影可控的流线追踪内收缩进气道设计方法。基于马赫数分布可控的轴对称基准流场,在指定进口水平投影为椭圆的条件下,采用该方法设计了内收缩进气道并在设计点(Ma=5.4)和接力点(Ma=4.0)对其进行数值研究。结果表明,设计点时进气道都能保持基准流场的波系结构和沿程压力分布,无粘时可以全捕获自由来流,喉道性能与基准流场几乎相等。有粘条件下,设计点和接力点时进气道具有较高的压缩效率和良好的流量捕获能力,接力点的流量系数高达0.85。该设计方法为内收缩进气道与乘波前体的一体化设计提供了新途径。     

可控曲率半径的圆柱形叶片逐点绘型方法

针对中低比转速离心泵,根据叶片进出口边界条件,以逐点绘型方法为基础,提出了一种新的曲率半径可控的叶片绘型方法。该方法的主要特点是曲率半径比值可作为设计常量由设计人员根据需要事先给定,随后分析了曲率半径及比例因子对叶片安放角、叶片包角、相对速度及速度矩等的影响。结果表明,不同曲率半径比值下的叶型参数及流动参数变化范围很大,曲率半径比值较大时,节流损失较大,泵扬程较低,曲率半径比值较小时,脱流损失较大,泵效率较低,存在较优的曲率半径比值区间[1.4,2.4],使叶片安放角平滑变化,泵的综合性能较优,在该优化区间内,取较大的曲率半径比值有利于获得较优的汽蚀性能,比例因子为0时叶片安放角的变化较为平稳,可用于开展离心泵的初步设计。     

精密导电滑环表面微槽车削性能

采用超精密车削精密导电滑环导电环的方法,保证了精密导电滑环绝缘环与导电环的同轴度、环间距,使绝缘微槽变形量低于0.10 mm。建立了精密导电滑环的切槽模型,利用仿真分析讨论了主轴转速、进给速率、刀具前角和切削深度对微槽变形量的影响,并对模型进行了试验验证。结果表明:滑环微槽侧面变形量随主轴转速的增大而变大,当转速达到700 r/min时,变形量达到了0.10 mm,超出了滑环的精度要求;滑环微槽变形量随机床进给速率的增大而变大,当进给速率达到1.5 mm/min时,变形量超出了滑环的精度要求;滑环微槽变形量随着前角的增大而减小;滑环微槽变形量随切削深度的增大而变大,切削深度低于0.2 mm时,滑环变形量微乎其微。